1-phase, 24 V DC (for S7-1500 and ET200MP)

Получить цену
0,926515658

Обзор

The design and functionality of the SIMATIC PM 1507 single-phase load power supply (PM = power module) with automatic range selection of the input voltage makes it an optimal match to the SIMATIC S7-1500 PLC. It supplies the S7-1500 system components such as CPU, system power supply (PS), I/O circuits of the input and output modules and, if necessary, the sensors and actuators with 24 V DC.

Дизайн

  • The load current supplies are directly fastened to the S7-1500 mounting rail (without connection to the backplane bus) and can be mounted directly to the left of the CPU (no installation clearance required)
  • Diagnostics LEDs to indicate status and faults: Operation, Fault, Stand-by
  • ON/OFF switches (operation/stand-by) in case of swapping modules
  • Mains connection plug with touch protection and strain relief for connection of input voltage (enables permanent wiring)
  • Plug-in 24 V DC output terminal with reverse polarity protection for connection of 24 V loads (enables permanent wiring)

Функции

  • Connection to all 1-phase 50/60 Hz networks (120 / 230 V AC) through automatic range switching
  • Short-term mains buffering
  • Output voltage of 24 V DC that is limited to maximum 28 V DC (prevents any damages in 24 V loads if input voltage is too high)
  • 50% 'Extra Power' for 5 seconds per minute for short-term overloads, for example, when switching on 24V consumers

Технические данные

Article number

6EP1332-4BA00

6EP1333-4BA00

Product

S7-1500 PM1507

S7-1500 PM1507

Power supply, type

24 V/3 A

24 V/8 A

Input

Input

1-phase AC

1-phase AC

Supply voltage

  • ? 1 at AC Rated value

120 V

120 V

  • ? 2 at AC Rated value

230 V

230 V

  • ? Note

Automatic range selection

Automatic range selection

Input voltage

  • ? 1 at AC

85 ... 132 V

85 ... 132 V

  • ? 2 at AC

170 ... 264 V

170 ... 264 V

Wide-range input

No

No

Overvoltage resistance

2.3 ? Vin rated, 1.3 ms

2.3 ? Vin rated, 1.3 ms

Mains buffering at Iout rated, min.

20 ms, at Vin = 93/187 V

20 ms, at Vin = 93/187 V

Rated line frequency 1

50 Hz

50 Hz

Rated line frequency 2

60 Hz

60 Hz

Rated line range

45 ... 65 Hz

45 ... 65 Hz

Input current

  • ? at rated input voltage 120 V

1.4 A

3.7 A

  • ? at rated input voltage 230 V

0.8 A

1.7 A

Switch-on current limiting (+25 °C), max.

23 A

62 A

Duration of inrush current limiting at 25 °C

  • ? maximum

3 ms

3 ms

I?t, max.

1.3 A?·s

12 A?·s

Built-in incoming fuse

T 3,15 A/250 V (not accessible)

T 6.3 A/250 V (not accessible)

Protection in the mains power input (IEC 898)

Recommended miniature circuit breaker: 10 A characteristic B or 6 A characteristic C

Recommended miniature circuit breaker: 16 A characteristic B or 10 A characteristic C

Output

Output

Controlled, isolated DC voltage

Controlled, isolated DC voltage

Rated voltage Vout DC

24 V

24 V

Total tolerance, static ±

1 %

1 %

Static mains compensation, approx.

0.1 %

0.1 %

Static load balancing, approx.

0.1 %

0.1 %

Residual ripple peak-peak, max.

50 mV

50 mV

Spikes peak-peak, max. (bandwidth: 20 MHz)

150 mV

150 mV

Product function Output voltage adjustable

No

No

Status display

LED green for 24 V OK, LED red for error, LED yellow for stand-by

LED green for 24 V OK, LED red for error, LED yellow for stand-by

On/off behavior

No overshoot of Vout (soft start)

No overshoot of Vout (soft start)

Startup delay, max.

1.5 s

1.5 s

Voltage rise, typ.

10 ms

10 ms

Rated current value Iout rated

3 A

8 A

Current range

0 ... 3 A

0 ... 8 A

Supplied active power typical

72 W

192 W

Short-term overload current

  • ? on short-circuiting during the start-up typical

12 A

35 A

  • ? at short-circuit during operation typical

12 A

35 A

Duration of overloading capability for excess current

  • ? on short-circuiting during the start-up

70 ms

70 ms

  • ? at short-circuit during operation

70 ms

70 ms

Parallel switching for enhanced performance

No

No

Efficiency

Efficiency at Vout rated, Iout rated, approx.

87 %

90 %

Power loss at Vout rated, Iout rated, approx.

11 W

21 W

Closed-loop control

Dynamic mains compensation (Vin rated ±15 %), max.

0.1 %

0.1 %

Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ.

1 %

2 %

Dynamic load smoothing (Iout: 10/90/10 %), Uout ± typ.

3 %

3 %

Load step setting time 10 to 90%, typ.

5 ms

5 ms

Load step setting time 90 to 10%, typ.

5 ms

5 ms

Setting time maximum

5 ms

5 ms

Protection and monitoring

Output overvoltage protection

Additional control loop, limitation (closed loop control) at <, 28.8 V

Additional control loop, limitation (closed loop control) at <, 28.8 V

Current limitation

3.15 ... 3.6 A

8.4 ... 9.6 A

Current limitation, typ.

3.4 A

9 A

Property of the output Short-circuit proof

Yes

Yes

Short-circuit protection

Electronic shutdown, automatic restart

Electronic shutdown, automatic restart

Overload/short-circuit indicator

-

-

Safety

Primary/secondary isolation

Yes

Yes

Galvanic isolation

Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 and EN 61131-2

Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 and EN 61131-2

Protection class

Class I

Class I

Leakage current

  • ? maximum

3.5 mA

3.5 mA

  • ? typical